Cecropin B抗菌肽接枝丝素蛋白膜的制备和表征

以体积分数为60%的乙醇处理制得不溶性再生丝素膜, 通过碳二亚胺法将Cecropin B抗菌肽共价接枝到丝素膜表面, 利用红外光谱、扫描电镜、X射线能谱和抗菌性测试等手段对制得的丝素膜结构和表面特性及其抗菌性能进行了测试分析. 结果表明, Cecropin B抗菌肽成功地接枝到了丝素膜的表面, 接枝后的丝素膜水溶性低, 并具有良好、 持久的抗菌能力.     

Mechanochemical Preparation of Water-Soluble Forms of Triterpene Acids

A waste-free technology for mechanochemical processing of fir needles into a biologically active preparation that regulates plant growth was developed. A preparation exhibiting cytokinin activity due to the presence in it of water-soluble forms of triterpene acids can be prepared using the proposed method. The effectiveness of the proposed method was confirmed by instrumental methods and biological tests.     

32Cr2MoVA合金结构钢标准物质的研制

本标准物质系合金钢。主要成份有碳、硅、锰、磷、硫、铬、镍、钼、钒,同时还含有锡、铅、砷、锑、铋等微量元素,每种元素成份都具有良好的线性关系。它可作为量值传递和仲裁分析的依据,同时也可用于校验分析仪器与分析方法的正确性和可靠性。     

复合生物材料的研究进展

从力学性能的改善和降解速率的可调度等角度,总结了复合生物材料与单一组分的材料相比,在生物医学领域应用中所表现出的综合使用性能的优越性。综述了复合生物材料,特别是用于骨修复的各类有机／无机复合材料近年来的研究进展状况。提出将与人骨中磷灰石微晶类似的羟基磷灰石纳米粒子与可降解聚酯材料进行复合,能够得到具有优越骨诱导性能并且能够降解的新型骨修复材料。这方面的研究代表了有机／无机复合生物材料领域新的发展方向。     

LLDPE/纳米SiO_2复合材料的力学性能和光学性能研究

采用熔融共混方法制备了LLDPE 纳米SiO2 复合材料 ,并对该体系的力学性能和光学性能进行了系统研究 .结果表明 ,随着纳米SiO2 的加入 ,复合材料的弹性模量显著提高 ,冲击强度与拉伸强度呈峰形变化 ,且均在SiO2 含量为 3phr左右达到最大值 .加入少量的纳米SiO2 后 ,复合材料薄膜对长波红外线 (7～ 1 1 μm)的吸收能力较LLDPE膜有了显著提高 ,透光率略有下降但雾度提高 ,透光质量得到改善 .同时表明 ,纳米SiO2 的表面处理方法对膜的光学性能有显著影响     

Li_3PO_4包覆LiMn_2O_4正极材料的结构表征和电化学性能

采用共沉淀法在尖晶石LiMn2O4颗粒表面包覆Li3PO4.XRD、SEM研究结果表明,包覆后的材料仍为尖晶石结构,粒径均匀.电化学性能测试表明,Li3PO4包覆层的存在,减少了正极材料与电解液的直接接触,抑制了高温下电解液对LiMn2O4材料的侵蚀,从而有效改善了高温下材料的循环性能.在40℃时,包覆样品的比容量衰减率都低于未包覆样品,其中包覆1%Li3PO4的样品的初始比容量为110.4mAh/g,50次循环后比容量为84.1mAh/g.     

Metal foams: A survey

The current state-of-the-art in the development of cellular metal foams is reviewed, with focus on their fabrication, mechanical/thermal/acoustic properties, and potential applications as lightweight panels, energy absorbers, heat exchangers, and acoustic liners. Foam property charts with scaling relations are presented, allowing scoping and selection through the use of material indices.     

Sol-gel polyimide-silica composite membrane: gas transport properties

The effect of introduction of silica particles prepared by the sol-gel technique on the gas transport properties of a polyimide film was studied. The sorption and permeation of N₂, O₂, CO₂, H₂ and CH₄ were studied and correlated with morphological changes in the polymer structure. From sorption isotherms, we observed that the composite membrane presents higher solubility coefficients than the polyimide one. The solubility coefficient ratio between the composite and the polyimide is about 1.5–2.0. The isotherms were analyzed in terms of the dual mode sorption. The Henry's coefficient and the Langmuir's affinity and saturation constants were obtained allowing to calculate the Langmuir to Henry concentration ratios as function of the gas pressure. These ratios decrease until zero within a certain pressure range as long as the Langmuir's mode is acting and they are higher for the polyimide membrane when compared with the composite one. This study was completed with calorimetric measurements during the sorption. The gas interaction energy in kJ/mol decreases within the same pressure range as previously described. The measured energies are higher for the polyimide film when compared with the composite one because the polyimide membrane presents a stronger energetic effect caused by a higher Langmuir's contribution. From permeation studies at 3.15⁵ Pa, the composite membrane showed higher permeability coefficients and permselectivities than the polyimide one. All these results were explained, taking into account the difference on the imidization degree of both membranes and the morphological changes which may be induced by the silica nodules in the organic/inorganic interphases.     

以多聚甲醛为还原剂制备新型阳极Pt/CMK-3催化剂

 以多聚甲醛为还原剂,采用液相还原法制备了Pt/CMK-3直接甲醇燃料电池(DMFC)阳极催化剂,并采用透射电镜和X射线衍射技术对其进行了表征. 结果表明,有序介孔碳CMK-3具有规整的二维有序孔道结构,为DMFC中电子和燃料的传输提供了方便的路径,同时它较大的比表面积使得Pt纳米粒子很好地分散在其表面; Pt/CMK-3催化剂中Pt粒子的平均粒径为2.8 nm, 小于E-TEK公司的商品化Pt/XC-72和以甲醇为还原剂制备的Pt/C-M催化剂,并且粒径分布范围窄,结晶度低. 察了Pt/CMK-3催化剂对甲醇的电催化氧化性能,发现Pt/CMK-3催化剂对甲醇氧化的电催化性能优于Pt/XC-72和Pt/C-M催化剂.